MOSFET - Metal Oxide Silicon Field Effect Transistors

MOSFET - Metal Oxide Silicon Field Effect Transistors

MOSFETs or Metal Oxide Silicon Field Effect Transistors, were invented to overcome the disadvantages posed by FETs, such as the slow operation, high drain resistance, and moderate input impedance. In this article, let us learn about the basics of MOSFET.

Table of Contents

  • MOSFET Basics
  • MOSFET Types
  • MOSFET Operating Regions
  • MOSFET as a Switch
  • MOSFET Applications
  • Frequently Asked Questions on MOSFET

MOSFET Basics

What Is a MOSFET?

Metal Oxide Silicon Field Effect Transistors commonly known as MOSFETs are electronic devices used to switch or amplify voltages in circuits. It is a voltage-controlled device and is constructed by three terminals. The terminals of MOSFET are named as follows:

  • Source
  • Gate
  • Drain
  • Body
The figure shows a practical MOSFET.
MOSFET Construction

The circuit of MOSFET is typically represented as follows:

  • The p-type semiconductor forms the base of the MOSFET.
  • The two types of the base are highly doped with an n-type impurity which is marked as n+ in the diagram.
  • From the heavily doped regions of the base, the terminals source and drain originate.
  • The layer of the substrate is coated with a layer of silicon dioxide for insulation.
  • A thin insulated metallic plate is kept on top of the silicon dioxide and it acts as a capacitor.
  • The gate terminal is brought out from the thin metallic plate.
  • A DC circuit is then formed by connecting a voltage source between these two n-type regions.

Working Principle of MOSFET

When voltage is applied to the gate, an electrical field is generated that changes the width of the channel region, where the electrons flow. The wider the channel region, the better conductivity of a device will be.

MOSFET Types

The classification of MOSFET based on the construction and the material used is given below in the flowchart.

MOSFETs are of two classes: Enhancement mode and depletion mode. Each class is available as n-channel or p-channel; hence overall they tally up to four types of MOSFETs.

Depletion Mode

When there is no voltage across the gate terminal, the channel shows maximum conductance. When the voltage across the gate terminal is either positive or negative, then the channel conductivity decreases.

Enhancement Mode

When there is no voltage across the gate terminal, then the device does not conduct. When there is the maximum voltage across the gate terminal, then the device shows enhanced conductivity.

The N-channel MOSFETs are abbreviated as NMOS and are symbolically represented as shown in the figure below:


Similarly, the P-channel MOSFETs are abbreviated as PMOS and are symbolically represented as follows:


Operating Regions of MOSFET

A MOSFET is seen to exhibit three operating regions. Here, we will discuss those regions.

Cut-Off Region

The cut-off region is a region in which there will be no conduction and as a result, the MOSFET will be OFF. In this condition, MOSFET behaves like an open switch.

Ohmic Region

The ohmic region is a region where the current (IDS)increases with an increase in the value of VDS. When MOSFETs are made to operate in this region, they are used as amplifiers.

Saturation Region

In the saturation region, the MOSFETs have their IDS constant in spite of an increase in VDS and occurs once VDS exceeds the value of pinch-off voltage VP. Under this condition, the device will act like a closed switch through which a saturated value of IDS flows. As a result, this operating region is chosen whenever MOSFETs are required to perform switching operations.

MOSFET as a Switch

MOSFETs are commonly used as switches. The circuit below shows the configuration of MOSFET when it is used as a switch.

In the circuit arrangement, an Enhancement-mode N-channel MOSFET is used to switch a simple lamp “ON” and “OFF.” The input fate voltage Vgs is adjusted to an appropriate positive voltage to switch “ON” the device and the voltage level is set to a negative value or zero to turn it “OFF.”

The switching characteristics for both N-channel and P-channel type MOSFET are summarised in the table below:

MOSFET TypeVGS ≪ 0VGS = 0VGS ≫ 0
N-channel EnhancementOFFOFFON
N-channel DepletionOFFONON
P-channel EnhancementONOFFOFF
P-channel DepletionONONOFF

MOSFET vs BJT

In this section, let us discuss some differences between MOSFET and BJT.

MOSFETBJT
There are two types of MOSFET and they are named: N-type or P-typeBJT is of two types and they are named as: PNP and NPN
MOSFET is a voltage-controlled deviceBJT is a current-controlled device
The input resistance of MOSFET is high.The input resistance of BJT is low.
Used in high-current applicationsUsed in low-current applications

MOSFET applications

  • Radiofrequency applications use MOSFET amplifiers extensively.
  • MOSFET behaves as a passive circuit element.
  • Power MOSFETs can be used to regulate DC motors.
  • MOSFETs are used in the design of the chopper circuit.

Advantages of MOSFET

  • MOSFETs operate at greater efficiency at lower voltages.
  • Absence of gate current results in high input impedance producing high switching speed.

Disadvantages of MOSFET

  • MOSFETs are vulnerable to damage by electrostatic charges due to the thin oxide layer.
  • Overload voltages make MOSFETs unstable.

Frequently Asked Questions on MOSFET

Q1

What is a MOSFET?

MOSFET or Metal Oxide Silicon Field Effect Transistors is a voltage-controlled four-terminal device that is used for switching and amplification purposes.

Q2

Can MOSFET conduct in both directions?

Yes, MOSFETs are bidirectional.

Q3

How many types of MOSFETs are there?

MOSFETs are of two classes: Enhancement mode and depletion mode. Each class is available as n-channel or p-channel; hence overall they tally up to four types of MOSFETs.

Q4

What are the operating regions of MOSFET?

There are three operating regions and they are named as: cut off region, ohmic region and saturation region.

Q5

What is the difference between a MOSFET and a BJT?

MOSFET is a voltage-controlled device while a BJT is a current-controlled device.

Comments

Post a Comment

Popular posts from this blog

Atomic Force Microscope

Image
Atomic Force Microscope: Principle, Parts, Uses The atomic force  microscope  (AFM) is a type of scanning probe microscope whose primary roles include measuring properties such as magnetism, height, friction. The resolution is measured in a nanometer, which is much more accurate and effective than the optical diffraction limit. It uses a probe for measuring and collection of data involves touching the surface that has the probe. An image is formed when the scanning probe microscope raster-scans the probe over a section of the sample, measuring its local properties concurrently. They also have piezoelectric elements, which are electric charges that accumulate in selected solid materials like  DNA , biological proteins, crystal, etc, to enable tiny accurate and precise movement during scanning upon an electric command. The Atomic Force Microscope was invented in 1982, by scientists working in IBM, just after the invention of the Scanning tunneling Microscope in 1980 by Ge...
Read more

Subject: Nano Technology

SEMESTER-7 Course: BE ECE SUBJECT: Nano Technology COURSE OBJECTIVE: To introduce and provide a broad view of the nascent field of nanotechnology to Undergraduates. To introduce students to inter- and multi-disciplinary science and engineering. Syllabus: Unit-1 Limitations of CMOS Fundamentals of MOSFET devices, Scaling of CMOS, Limitations, Alternative concepts in materials, Structures of MOS devices: SOI MOSFET, FINFETS, Dual Gate MOSFET, Ferroelectric FETs. Unit-II Micro and Nano Fabrication Optical Lithography, Electron beam Lithography, Atomic Lithography, Molecular beam epitaxy, Nano-lithography. Unit-III Characterization Equipments  Principles of Electron Microscopes, Scanning Electron Microscope, Transmission Electron Microscope, Atomic Force Microscope, Scanning Tunneling Microscope. Unit-IV Nano Devices-1 Resonant tunneling diodes, Single electron devices, Josephson junction, Single Flux Quantum logic, Molecular electronics Unit-V Nano Devices-11 Quantum computing princip...
Read more

Resonant Tunneling Diodes (RTD)

Image
Concept of Resonant Tunneling An interesting phenomena occurs when two barriers of width a separated by a potential well of a small distance 𝐿 as shown in fig. This leads to the concept of resonant tunneling. Fig.: Double barrier junction with no applied bias.   The barriers are sufficiently thin to allow tunneling and the well region between the two barriers is also sufficiently narrow to form discrete (quasi-bound) energy levels. The transmission coefficient of the double symmetric barrier becomes unity. (ie., T = 1) , when the energy of the incoming electron wave ( 𝐸 ) coincides with the energy of one of the discrete states formed by the well. Thus, transmission probability of the double symmetric barrier is maximum; hence, the tunneling current reaches peak value when the electron wave's energy is equal to the well's quantized energy state. This phenomenon is known as resonance tu...
Read more